{"id":1510,"date":"2015-01-07T04:58:20","date_gmt":"2015-01-07T04:58:20","guid":{"rendered":"https:\/\/permabond.com\/troubleshooting-singlepart-epoxy-adhesive-dispensing-problem\/"},"modified":"2025-02-25T11:23:01","modified_gmt":"2025-02-25T11:23:01","slug":"troubleshooting-singlepart-epoxy-adhesive-dispensing-problem","status":"publish","type":"post","link":"https:\/\/permabond.com\/de\/troubleshooting-singlepart-epoxy-adhesive-dispensing-problem\/","title":{"rendered":"Troubleshooting Single-part Epoxy Adhesive Dispensing Problem"},"content":{"rendered":"<h2><b>Manual Dispensing from Cartridge<\/b><\/h2>\n<p>On many epoxy adhesive cartridges, there is a strong plastic stopper. Cut the stopper with a sharp Stanley knife (or similar implement) before affixing the dispensing nozzle.<\/p>\n<p>Typically, 320ml cartridges fit in regular caulking guns. However, certain epoxy adhesive products with high viscosity may prove difficult to dispense if pumping by hand. For these use a gun \u201cupgrade\u201d with more sophisticated ratcheting or pneumatically operated by a compressed airline.<\/p>\n<h2><b>Cold Dispensing Conditions<\/b><\/h2>\n<p><a href=\"https:\/\/permabond.com\/products\/epoxies-single-part\/\">Epoxy<\/a> adhesive thickens when cold, so if you are using the adhesive straight from the refrigerator or working in a cold environment, it will become much more difficult to dispense. Some high viscosity grades may become virtually impossible to dispense from a cartridge.\u00a0 In this case, you can warm the epoxy adhesive to reduce the viscosity to something more workable. However, warming the epoxy adhesive will eventually cause it to gel and shorten its shelf life in the cartridge \u2013 especially if repeatedly taken out of the fridge, warmed up and then put back in the fridge.<\/p>\n<h2><b>Common Single-part Epoxy Adhesive Dispensing Problems<\/b><\/h2>\n<p>Epoxy Adhesive not coming out of cartridge:<\/p>\n<ul>\n<li>Check \u2013 the tip has been cut off and the adhesive is visible inside.<\/li>\n<li>Without putting the nozzle on, try to dispense some adhesive directly from the mouth of the cartridge. It may be necessary to trim the nozzle to a larger diameter to reduce the back pressure in the cartridge to allow the adhesive to be dispensed.<\/li>\n<li>If nothing is coming out, unfurl a paper clip and poke it into the mouth of the cartridge to see if the adhesive has gone hard.<\/li>\n<li>If it has gone thick, you can warm it and then see if you can dispense. If not it could be time to get some fresh stock. Be very careful to warm it gently e.g. 30\u00b0C and check every 10 minutes. Heating it too much could cause the material to exotherm.<\/li>\n<li>If the adhesive is still liquid and doesn\u2019t come out, check the gun is functioning properly and the plunger fits properly against the back piston in the cartridge.<\/li>\n<li>As mentioned, some products are high viscosity and difficult to dispense manually. You may need a compressed air gun or dispensing equipment.<\/li>\n<\/ul>\n<h2><b>Automatic Dispensing Equipment<\/b><\/h2>\n<p>As the product is single component and does not require mixing, it lends itself to a simple dispensing equipment set-up, either by automated dispensing from a cartridge or from bulk with a follower plate pushing the adhesive down and forcing it up a tube.\u00a0 If experiencing problems, check the following:<\/p>\n<ul>\n<li>Ensure the machine is switched on and has power<\/li>\n<li>Compressed air supply is operative<\/li>\n<li>Check for any blockages, ensure adhesive hasn\u2019t gelled in any parts of the equipment<\/li>\n<li>Check any bulk single-part epoxy adhesive is still liquid and hasn\u2019t thickened (or allow it to come up to room temperature if it is cold fresh from the refrigerator).<\/li>\n<li>Check the follower plate is the correct diameter for the adhesive packaging (check for any lip or rim which may interfere with the follower plate.<\/li>\n<li>Check the pipeline and nozzle are the right diameter and are compatible with the rheology of the single-part epoxy.<\/li>\n<\/ul>\n<h2>Top Single-part Epoxy Adhesive Dispensing Tips<\/h2>\n<ul>\n<li>After use, remove parts from dispensing equipment for cleaning. Metal parts can be soaked in solvent overnight.<\/li>\n<li>Bulk single \u2013part epoxy adhesive should be stored in the refrigerator.<\/li>\n<\/ul>\n<p>For further help, please contact the Permabond technical team <a href=\"https:\/\/permabond.com\/contact-us\">here<\/a>.<br \/>\n<a href=\"https:\/\/permabond.com\/wp-content\/uploads\/2022\/11\/dispensing-ES-1.jpg\"><img fetchpriority=\"high\" decoding=\"async\" class=\"alignleft size-full wp-image-621\" src=\"https:\/\/permabond.com\/wp-content\/uploads\/2022\/11\/dispensing-ES-1.jpg\" alt=\"dispensing epoxy adhesive\" width=\"478\" height=\"283\" \/><\/a><\/p>\n","protected":false},"excerpt":{"rendered":"<p>Manual Dispensing from Cartridge On many epoxy adhesive cartridges, there is a strong plastic stopper. Cut the stopper with a sharp Stanley knife (or similar implement) before affixing the dispensing nozzle. Typically, 320ml cartridges fit in regular caulking guns. However, certain epoxy adhesive products with high viscosity may prove difficult to dispense if pumping by [&hellip;]<\/p>\n","protected":false},"author":5,"featured_media":1511,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"footnotes":""},"categories":[607,613],"tags":[131,132,133,101,134,135,136,137,138],"class_list":["post-1510","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-adhesive-selection-and-use","category-troubleshooting-2","tag-automated-dispensing","tag-automatic-dispensing","tag-dispensing-gun","tag-epoxy-adhesive","tag-heat-cure-epoxy","tag-manual-dispensing","tag-pneumatic-gun","tag-single-part-epoxy","tag-single-part-epoxy-adhesive-dispensing"],"acf":[],"yoast_head":"<!-- This site is optimized with the Yoast SEO Premium plugin v27.3 (Yoast SEO v27.3) - https:\/\/yoast.com\/product\/yoast-seo-premium-wordpress\/ -->\n<title>Troubleshooting Single-part Epoxy Adhesive Dispensing Problems<\/title>\n<meta name=\"description\" content=\"This article provides solutions and tips for problems associated with manual, cold and automatic dispensing of single-part heat-cure epoxy adhesives\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/permabond.com\/de\/troubleshooting-singlepart-epoxy-adhesive-dispensing-problem\/\" \/>\n<meta property=\"og:locale\" content=\"de_DE\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"Troubleshooting Single-part Epoxy Adhesive Dispensing Problem\" \/>\n<meta property=\"og:description\" content=\"This article provides solutions and tips for problems associated with manual, cold and automatic dispensing of single-part heat-cure epoxy adhesives\" \/>\n<meta property=\"og:url\" content=\"https:\/\/permabond.com\/de\/troubleshooting-singlepart-epoxy-adhesive-dispensing-problem\/\" \/>\n<meta property=\"og:site_name\" content=\"Permabond\" \/>\n<meta property=\"article:publisher\" content=\"https:\/\/www.facebook.com\/permabondEA\/\" \/>\n<meta property=\"article:published_time\" content=\"2015-01-07T04:58:20+00:00\" \/>\n<meta property=\"article:modified_time\" content=\"2025-02-25T11:23:01+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/permabond.local\/wp-content\/uploads\/2022\/11\/dispensing-ES-1.jpg\" \/>\n\t<meta property=\"og:image:width\" content=\"478\" \/>\n\t<meta property=\"og:image:height\" content=\"283\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/jpeg\" \/>\n<meta name=\"author\" content=\"Laurie Gibbons\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:creator\" content=\"@PermabondEA\" \/>\n<meta name=\"twitter:site\" content=\"@PermabondEA\" \/>\n<meta name=\"twitter:label1\" content=\"Verfasst von\" \/>\n\t<meta name=\"twitter:data1\" content=\"Laurie Gibbons\" \/>\n\t<meta name=\"twitter:label2\" content=\"Gesch\u00e4tzte Lesezeit\" \/>\n\t<meta name=\"twitter:data2\" content=\"3\u00a0Minuten\" \/>\n<!-- \/ Yoast SEO Premium plugin. -->","yoast_head_json":{"title":"Troubleshooting Single-part Epoxy Adhesive Dispensing Problems","description":"This article provides solutions and tips for problems associated with manual, cold and automatic dispensing of single-part heat-cure epoxy adhesives","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/permabond.com\/de\/troubleshooting-singlepart-epoxy-adhesive-dispensing-problem\/","og_locale":"de_DE","og_type":"article","og_title":"Troubleshooting Single-part Epoxy Adhesive Dispensing Problem","og_description":"This article provides solutions and tips for problems associated with manual, cold and automatic dispensing of single-part heat-cure epoxy adhesives","og_url":"https:\/\/permabond.com\/de\/troubleshooting-singlepart-epoxy-adhesive-dispensing-problem\/","og_site_name":"Permabond","article_publisher":"https:\/\/www.facebook.com\/permabondEA\/","article_published_time":"2015-01-07T04:58:20+00:00","article_modified_time":"2025-02-25T11:23:01+00:00","og_image":[{"width":478,"height":283,"url":"https:\/\/permabond.local\/wp-content\/uploads\/2022\/11\/dispensing-ES-1.jpg","type":"image\/jpeg"}],"author":"Laurie Gibbons","twitter_card":"summary_large_image","twitter_creator":"@PermabondEA","twitter_site":"@PermabondEA","twitter_misc":{"Verfasst von":"Laurie Gibbons","Gesch\u00e4tzte Lesezeit":"3\u00a0Minuten"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"Article","@id":"https:\/\/permabond.com\/de\/troubleshooting-singlepart-epoxy-adhesive-dispensing-problem\/#article","isPartOf":{"@id":"https:\/\/permabond.com\/de\/troubleshooting-singlepart-epoxy-adhesive-dispensing-problem\/"},"author":{"name":"Laurie Gibbons","@id":"https:\/\/permabond.local\/#\/schema\/person\/ee2cd0b49e7331ee4adc67eafbdc21f6"},"headline":"Troubleshooting Single-part Epoxy Adhesive Dispensing Problem","datePublished":"2015-01-07T04:58:20+00:00","dateModified":"2025-02-25T11:23:01+00:00","mainEntityOfPage":{"@id":"https:\/\/permabond.com\/de\/troubleshooting-singlepart-epoxy-adhesive-dispensing-problem\/"},"wordCount":576,"publisher":{"@id":"https:\/\/permabond.local\/#organization"},"image":{"@id":"https:\/\/permabond.com\/de\/troubleshooting-singlepart-epoxy-adhesive-dispensing-problem\/#primaryimage"},"thumbnailUrl":"https:\/\/permabond.com\/wp-content\/uploads\/2022\/11\/dispensing-ES-1.jpg","keywords":["automated dispensing","automatic dispensing","dispensing gun","Epoxy Adhesive","heat-cure epoxy","manual dispensing","pneumatic gun","single-part epoxy","Single-part Epoxy Adhesive Dispensing"],"articleSection":["Adhesive Selection and Use","Troubleshooting"],"inLanguage":"de"},{"@type":"WebPage","@id":"https:\/\/permabond.com\/de\/troubleshooting-singlepart-epoxy-adhesive-dispensing-problem\/","url":"https:\/\/permabond.com\/de\/troubleshooting-singlepart-epoxy-adhesive-dispensing-problem\/","name":"Troubleshooting Single-part Epoxy Adhesive Dispensing Problems","isPartOf":{"@id":"https:\/\/permabond.local\/#website"},"primaryImageOfPage":{"@id":"https:\/\/permabond.com\/de\/troubleshooting-singlepart-epoxy-adhesive-dispensing-problem\/#primaryimage"},"image":{"@id":"https:\/\/permabond.com\/de\/troubleshooting-singlepart-epoxy-adhesive-dispensing-problem\/#primaryimage"},"thumbnailUrl":"https:\/\/permabond.com\/wp-content\/uploads\/2022\/11\/dispensing-ES-1.jpg","datePublished":"2015-01-07T04:58:20+00:00","dateModified":"2025-02-25T11:23:01+00:00","description":"This article provides solutions and tips for problems associated with manual, cold and automatic dispensing of single-part heat-cure epoxy adhesives","breadcrumb":{"@id":"https:\/\/permabond.com\/de\/troubleshooting-singlepart-epoxy-adhesive-dispensing-problem\/#breadcrumb"},"inLanguage":"de","potentialAction":[{"@type":"ReadAction","target":["https:\/\/permabond.com\/de\/troubleshooting-singlepart-epoxy-adhesive-dispensing-problem\/"]}]},{"@type":"ImageObject","inLanguage":"de","@id":"https:\/\/permabond.com\/de\/troubleshooting-singlepart-epoxy-adhesive-dispensing-problem\/#primaryimage","url":"https:\/\/permabond.com\/wp-content\/uploads\/2022\/11\/dispensing-ES-1.jpg","contentUrl":"https:\/\/permabond.com\/wp-content\/uploads\/2022\/11\/dispensing-ES-1.jpg","width":478,"height":283},{"@type":"BreadcrumbList","@id":"https:\/\/permabond.com\/de\/troubleshooting-singlepart-epoxy-adhesive-dispensing-problem\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/permabond.local\/de\/"},{"@type":"ListItem","position":2,"name":"Troubleshooting Single-part Epoxy Adhesive Dispensing Problem"}]},{"@type":"WebSite","@id":"https:\/\/permabond.local\/#website","url":"https:\/\/permabond.local\/","name":"Permabond","description":"Permabond","publisher":{"@id":"https:\/\/permabond.local\/#organization"},"alternateName":"Permabond Engineering Adhesives","potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/permabond.local\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"de"},{"@type":"Organization","@id":"https:\/\/permabond.local\/#organization","name":"Permabond Engineering Adhesives","alternateName":"Permabond","url":"https:\/\/permabond.local\/","logo":{"@type":"ImageObject","inLanguage":"de","@id":"https:\/\/permabond.local\/#\/schema\/logo\/image\/","url":"https:\/\/permabond.com\/wp-content\/uploads\/2022\/09\/permabond-logo-BLUE-1.png","contentUrl":"https:\/\/permabond.com\/wp-content\/uploads\/2022\/09\/permabond-logo-BLUE-1.png","width":1371,"height":243,"caption":"Permabond Engineering Adhesives"},"image":{"@id":"https:\/\/permabond.local\/#\/schema\/logo\/image\/"},"sameAs":["https:\/\/www.facebook.com\/permabondEA\/","https:\/\/x.com\/PermabondEA","https:\/\/www.linkedin.com\/company\/permabond-engineering-adhesives"]},{"@type":"Person","@id":"https:\/\/permabond.local\/#\/schema\/person\/ee2cd0b49e7331ee4adc67eafbdc21f6","name":"Laurie Gibbons","image":{"@type":"ImageObject","inLanguage":"de","@id":"https:\/\/secure.gravatar.com\/avatar\/ef30a45eda5c8ff1e3f4c6288df66f8a58ab5b054fecced621a7c58e0e6fe4ba?s=96&r=g","url":"https:\/\/secure.gravatar.com\/avatar\/ef30a45eda5c8ff1e3f4c6288df66f8a58ab5b054fecced621a7c58e0e6fe4ba?s=96&r=g","contentUrl":"https:\/\/secure.gravatar.com\/avatar\/ef30a45eda5c8ff1e3f4c6288df66f8a58ab5b054fecced621a7c58e0e6fe4ba?s=96&r=g","caption":"Laurie Gibbons"},"description":"Laurie has worked in the adhesive industry for over 30 years. With backgrounds in formulating, technical support, quality, sales, management, and marketing, her well-rounded experience supports Permabond clients and the Permabond team.","jobTitle":"Business Development Manager"}]}},"_links":{"self":[{"href":"https:\/\/permabond.com\/de\/wp-json\/wp\/v2\/posts\/1510","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/permabond.com\/de\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/permabond.com\/de\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/permabond.com\/de\/wp-json\/wp\/v2\/users\/5"}],"replies":[{"embeddable":true,"href":"https:\/\/permabond.com\/de\/wp-json\/wp\/v2\/comments?post=1510"}],"version-history":[{"count":0,"href":"https:\/\/permabond.com\/de\/wp-json\/wp\/v2\/posts\/1510\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/permabond.com\/de\/wp-json\/wp\/v2\/media\/1511"}],"wp:attachment":[{"href":"https:\/\/permabond.com\/de\/wp-json\/wp\/v2\/media?parent=1510"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/permabond.com\/de\/wp-json\/wp\/v2\/categories?post=1510"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/permabond.com\/de\/wp-json\/wp\/v2\/tags?post=1510"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}